Metrohm 732 IC Detector Bedienungsanleitung Seite 108
- Seite / 223
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4.5 Measurement parameters
732 IC Detector / 733 IC Separation Center
101
>PARAM
>PARAM/709 IC Pump
Settings for 709 IC Pump
This submenu appears only with "SETUP/peripherals/operation with
709 = on".
These settings are effective only if the 709 IC Pump is con-
nected to the 732 IC Detector and the remote control is acti-
vated with the <EXT.> key (see section 2.6.1).
>PARAM/709 IC Pump
flow 0.50 mL/min
0.01…5.00 mL/min
Flow rate
Flow rate of the 709 IC Pump.
>PARAM/709 IC Pump
Pmax 10.0 MPa
0.1…50 MPa
Maximum shutoff pressure
Maximum shutoff pressure for the automatic shutoff of
the pump drive of the 709 IC Pump to protect the
separating column against excessive pressure.
This limit value should be ca. 3 MPa (= 30 bar) above
the normal operating pressure of the separating column
used or correspond to the maximum admissible oper-
ating pressure of the separating column.
If the 709 Pump exceeds the specified limit value, the
pump drive is switched off within a pump cycle and
blocked, at the same time the bottom line of the display
of the 732 IC Detector shows the message "stopped:
YY-MM-DD HH:MM" with details of the time when the
pump was stopped. The LED "P
max
" on the 709 IC
Pump flashes, the shutoff pressure can be requested
under "P
actual
".
A 709 IC Pump stopped in this manner is put back into
operation as follows:
• Press <EXT.> key to switch off remote opera-
tion.
• Press <R/S> key to remove block. The LED
"P
max
" no longer flashes.
• Press <EXT.> key to switch remote operation
back on.
>PARAM/709 IC Pump
Pmin 0.0 MPa
0.0…50 MPa
Minimum shutoff pressure
Minimum shutoff pressure for the automatic shutoff of
the pump drive of the 709 IC Pump to protect the IC
system when leaks occur or the eluent supply is inter-
rupted.
This limit value should be sufficiently far below the
normal operating pressure of the separating column
used. The entry of "0.0" switches the automatic shutoff
off.
If the pressure value of the 709 IC Pump is below the
specified limit value for a considerable length of time,
the pump drive of the pump is switched off and
blocked, at the same time the bottom line of the display
- 732 IC Detector 1
- 733 IC Separation Center 1
- Table of contents 2
- List of figures 6
- 1.2 Parts and controls 10
- 1313121211111010 11
- 1818 1717 1616 1515 1414 11
- IC Separation Center733 12
- FILL INJECT 12
- 1 Introduction 13
- 1.3.1 Organization 15
- >PARAM/detector 16
- 1.4 Safety notes 17
- 2 Installation 18
- 2.2.1 Packaging 19
- 2.2.2 Check 19
- 2.2.3 Location 19
- 6.2125.090 20
- 6.2125.0906.2125.090 22
- 2.4 Mains connection 24
- 2.4.2 Fuses 25
- 2.5 Capillary connections 26
- 50504949 5151 5252 27
- 6.2125.060 28
- 2.6.3 Filter unit PEEK 29
- 2.6.4 Filter unit Manufit 30
- 2222 6464 6565 32
- 6666 65656767 6868 32
- 5656 7070 33
- 2.7 Precolumns 35
- Injektor 36
- 94949090 45
- 1 2 3 4 5 6 7 8 9 50
- 2.9.7 Connection of a PC 51
- 3 Operating tutorial 52
- 3.2 Preparations 53
- 3.3 Putting into operation 55
- ">" and 61
- 151.2 µµS/cm 8.9 min 65
- 151.2 µµS/cm 53.2 min 65
- 3.4 Calibration 66
- OVERLOAD 67
- +0.000 µµS/cm 0.0 min 68
- 3.5 Sample determination 69
- 3.6 Storing as a method 71
- "Water" for 73
- "Water" 73
- 4.2.1 Display 78
- Key field of 732 IC Detector 79
- "active") 80
- "cycle" 80
- ":" 83
- 4.2.3 Instrument dialog 84
- Main menu 84
- Inquiries 84
- 4.2.4 Data entry 86
- 4.2.5 Text entry 87
- ">CONFIG/detector/ 88
- ">CONFIG/ 88
- 4.3.2 Status messages 89
- 4.4 Basic settings 91
- "off °C" 96
- 4.5 Measurement parameters 104
- --------" 105
- "full scale" 106
- "08:34") 107
- 709 = on" 108
- 4.5.2 <FULL SCALE>key 109
- 4.6 Triggering of functions 110
- 4.6.2 <INJECT> keys 111
- ZERO ZERO 112
- ZERO OFF 113
- PUMP R/S 113
- 4.7 Programming 114
- "disabled" 115
- "range", see sec 118
- "full scale", see 118
- TTTTTTTT 119
- "Pmin", see sec 120
- 4.7.2 <PROG R/S> key 121
- 4.7.3 <EVENT> key 121
- "---" means that no 122
- "flag", the program 122
- "prog R/S" 123
- 4.7.4 <METHOD> key 124
- 4.8 Data output 126
- "ZEROREF" 127
- "OVERLOAD" 127
- "BACKGROUND" 127
- ">CONFIG/print 127
- 4.8.2 <PLOT> key 129
- Preparations 129
- Print header 130
- Identification 1 130
- Identification 2 130
- Date and time 130
- 4.8.3 <REPORT> key 131
- 4.9 Examples of methods 133
- General conditions 136
- Configuration 136
- Settings for 709 IC Pump 138
- Settings for 752 Pump Unit 138
- 4 Operation 139
- 5.1.1 Separating columns 140
- 5.1.2 Pumps 141
- 5.1.3 Eluents 142
- 5.1.4 Suppressor module 143
- 5.1.5 Connections 143
- 5.2.1 General information 143
- 5.2.2 Passivation 144
- 5.2.3 Recycling 144
- 5.2.4 Shutdown 144
- 100100999998989797 149
- 5.3 Faults and malfunctions 152
- 5.4 Diagnostic tests 156
- 5.4.2 Prepare instruments 157
- 5.4.4 Check keypad 158
- 5.4.5 Check display 159
- 5.4.6 Check RS232 interfaces 160
- 5.4.8 Internal hardware test 162
- 5.4.9 Initialize data memory 164
- 5.5 Validation / GLP 166
- 6 Interfaces 168
- 6.1.2 Call-up of objects 169
- 6.1.3 Triggers 170
- 6.1.4 Status messages 171
- 6.1.5 Error messages 172
- &Setup.Save" 180
- Check offset $G, $S 182
- >CONFIG/RS 184
- 6.1.8 Handshake 185
- 6.1.9 Pin assignment 188
- HWs". The 189
- 6.3 Analog output 194
- 6.5 Valve interfaces 195
- 7 Appendix 196
- 2.732.0010 200
- 2.732.0110 200
- 16" 201
- 7.3 Optional accessories 203
- 7.4 Warranty and conformity 211
- EU Declaration of Conformity 212
- 7.5 Index 216
Verwandte Produkte und Handbücher für Ausrüstung Metrohm 732 IC Detector
(54 Seiten)
(182 Seiten)
Ausrüstung Metrohm TiNet 2.5 Bedienungsanleitung
(80 Seiten)
(80 Seiten)
(38 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.954 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern