Metrohm 762 IC Interface Bedienungsanleitung

762 IC Interface762 IC InterfaceMetrohmMetrohmSYSTEM 1SYSTEM 2RUNSTOPRUN/STOPRUN/STOP8.762.1003Instructions for UseMETROHM Ltd.CH-9101 HerisauSwitzerl

1 Introduction762 IC Interface61.3 Information on the Instructions for UsePlease read through these Instructions for Use carefully before you putthe

1.3 Information on the Instructions for Use762 IC Interface 71.3.2 Notation and pictogramsThe following notations and pictograms (symbols) are used

1 Introduction762 IC Interface81.4 Safety notesWhile electrical safety in the handling of the 762 IC Interface is assuredin the context of the speci

2.1 Setting up the instrument762 IC Interface 92 Installation2.1 Setting up the instrument2.1.1 PackagingThe 762 IC Interface is supplied together

2 Installation762 IC Interface102.2 Mains connection2.2.1 Mains voltage and fusesThe 762 Interface has a power supply which automatically adjusts i

2.3 Connection to the PC762 IC Interface 112.3 Connection to the PC2.3.1 Connecting cableAlways switch off 762 IC Interface and PC before you conne

2 Installation762 IC Interface122.4 Connection of external instruments2.4.1 General informationBefore an external instrument is connected to the 76

2.4 Connection of external instruments762 IC Interface 13• 750 Autosampler:Always switch on the 762 IC Interface first and then the 750Autosampler.•

2 Installation762 IC Interface142.4.3 752 Pump UnitExampleAnalysis of anions or cations on a modular system with chemical sup-pression.Instruments•

2.4 Connection of external instruments762 IC Interface 152.4.4 753 Suppressor ModuleExampleSimultaneous analysis of cations and anions on a modular

CH-9101 Herisau/SwitzerlandTel. ++41 71 353 85 85Fax ++41 71 353 89 01Internet www.metrohm.chE-Mail [email protected] IC Interface762 IC InterfaceMe

2 Installation762 IC Interface162.4.5 754 Dialysis UnitExampleAnalysis of anions on a modular system with chemical suppression af-ter preceding samp

2.4 Connection of external instruments762 IC Interface 172.4.6 750 AutosamplerExampleAutomatic analysis of anions or cations on a modular system wit

2 Installation762 IC Interface182.4.7 766 IC Sample ProcessorExampleAutomatic analysis of anions or cations on a modular system with elec-tronic sup

2.4 Connection of external instruments762 IC Interface 192.4.8 791 VA DetectorExampleAnalysis of anions or cations on a modular system with electron

2 Installation762 IC Interface202.4.9 761 Compact ICExampleConnection of a modular system and a 761 Compact IC to a 762 IC In-terface (if not enough

3.1 Manual operation762 IC Interface 213 Operation3.1 Manual operationSwitch instrument on/offThe 762 IC Interface 762 is switched on and off using

3 Operation762 IC Interface223.2 Operation via «IC Net»This section describes only the most important points concerning theoperation of the 762 IC I

3.2 Operation via «IC Net»762 IC Interface 23Second press on RUN/STOP means 'stop' when measuringIf this option is enabled, the running dat

3 Operation762 IC Interface24FIFO size Intermediate memory in byte.Selection: 1...16Default value: 16<ASK> Read current parameters from 762 IC

3.2 Operation via «IC Net»762 IC Interface 253.2.2 Event output linesThe 762 System [#] window with programs and settings for the sevenevent output

Table of contents762 IC Interface ITable of contents1 Introduction...

3 Operation762 IC Interface26ProgramOn the Program subpage, program steps including time, program in-struction and parameter can be entered.First co

3.2 Operation via «IC Net»762 IC Interface 27Events configurationOn the Events configuration subtab user-defined event commands canbe defined, which

3 Operation762 IC Interface28Events setupThe Events setup tab of the 762 System [#] window contains the startupvalues for the seven event output line

4.1 Technical data762 IC Interface 294 Appendix4.1 Technical dataMains connectionVoltage 100...240 VFrequency 50...60 HzPower consumption 7 VAFuse

4 Appendix762 IC Interface30FIFO 0…16 Bytes (for Dev. 8 not available)Pin assignmentPin 2: RxD (Received Data) for Dev. 1…4Pin 3: TxD (Transmitted Da

4.1 Technical data762 IC Interface 31Zero error ± 2.5 mVPin assignmentPin 1,4,5,8,9: GND (ground, connected tohousing)Pin 2: Analog 1+Pin 3: Analog 1

4 Appendix762 IC Interface324.2 Scope of deliverySubject to changes !All dimensions are given in mm.The 762 IC Interface is available in the two fol

4.3 Optional accessories762 IC Interface 334.3 Optional accessories6.2128.180 Remote connection cableConnection cable 762 IC Interface –752, 753, 75

4 Appendix762 IC Interface344.4 Warranty and conformity4.4.1 WarrantyThe warranty on our products is limited to defects that are traceable tomateri

4.4 Warranty and conformity762 IC Interface 354.4.2 EU Declaration of conformityEU Declaration of ConformityThe Metrohm AG company, Herisau, Switzer

Table of contents762 IC InterfaceIIList of figuresFig. 1: Connection possibilities at 762 IC Interface ...

4 Appendix762 IC Interface364.4.3 Certificate of conformity and system validationCertificate of Conformity and System ValidationThis is to certify t

4.5 Index762 IC Interface 374.5 Index7709 IC PumpConnection to 762... 13Settings...

4 Anhang762 IC Interface38PPackaging...9Parity... 23Parity

1.1 Instrument description762 IC Interface 11 Introduction1.1 Instrument descriptionThe 762 IC Interface provides the connection between the PC a

1 Introduction762 IC Interface21.2 Parts and controls1.2.1 2.762.0010 IC Interface3344762 IC InterfaceMetrohmMetrohmSYSTEM 1RUN/STOP1122 Fig. 2: F

1.2 Parts and controls762 IC Interface 3101012121313141499RunComStartSystem 1EventsMade by Metrohm Herisau Switzerlandf = 50-60 Hz100 - 240 VType 1.7

1 Introduction762 IC Interface41.2.2 2.762.0020 IC Interface3344762 IC InterfaceMetrohmMetrohm5566SYSTEM 1SYSTEM 2RUNSTOPRUN/STOPRUN/STOP1122 Fig. 4

1.2 Parts and controls762 IC Interface 5101012121313141499ComRunRunComStartStart 1 2 3 4 5 6 7EventsSystem 2Channels 3/4Dev. 4/8Dev. 3/7Dev. 2/6Dev.